-
Out of stock
Genuine Kawasaki ~ Used Kawasaki P/N's: 44039-1005 Upper 44037-1008 Lower 46012-008 Handlebar Holder 92007-002 Bolt Set 461F0800 Washers (in set) -
Out of stock
Harley P/N: 16674-73B Applications:- 1973-1978 Sportster
-
Out of stock
Fork outer tubes have been brush polished. Set includes:- 44005-063 LH Outer Tube
- 44006-061 RH Outer Tube
- 44009-024 Fork Seals
- 44010-032 Dust Shields
- 220B0408A Screws
- 44045-002 Seals
- 76-77 KZ900A
- 76 KH500
- 77 KZ1000A
- 76 KZ900 LTD
- May fit others
-
Out of stock
Kawasaki Genuine Part ~ New Old Stock Kawasaki P/N: 23003-013 Application:- 1972 H2 750
-
No title. 2141 miles. This bike was hit from behind. Missing many parts. Carbs missing many parts. WILL SEPARATE! Possible low cost shipping on request. -
This wheel assembly is great for unrestored every day rider. Rim has some marks and a few rust spots, otherwise very nice. OEM Kawasaki P/N: 42048-041 Consists of:- 41025-058 Genuine Takasago 2.5 x 18 rim
- (20) 41027-090 inner spokes
- (20) 41028-089 outer spokes
- KZ650
-
Genuine Kawasaki Parts ~ Used This is correct for 1975 Z1 900 (Shift pattern numbers were stamped smaller) but will work on 1974 and up. Great part for the restored bike. Includes Kawasaki P/N:- 14026-026 Chain Cover (1)
- 14026-012 Inspection Cover
- 14045-012 Gasket
- 220B0612 Screws (2)
- 74-75 Z1 900
- 76-77 KZ900A
- 1976 KZ900 LTD
-
Genuine Kawasaki, reconditioned Kawasaki P/N: 43041-1013 Applications:- 1980 KZ1000D Z1R
- 1979-1980 KZ1000A MKII
- 1979-1981 KZ1000C Police
-
We have had this seat in our warehouse for many years. This seat has never been mounted, we were told it fits a Honda 90. Not sure of the application. It could use a good clean up, we just wiped off the dirt. -
Used set of cams for Z1 900, polished. Hollow cams Correct hollow shaft for 1973 and Early 1974 Z1- 12044-004 Intake
- 12044-005 Exhaust
- 1973 Z1 900 and Early 1974
-
No broken parts, tank does not appear to leak. Tank is 5 gallons and the inside is nice. Harley P/N: 61202-67 Applications:- 1967-1977 FLH
-
Out of stock
Brush finish. Set of 2. Some have lower bracket as shown for fender brace, and some do not. Kawasaki uses the same part number for both versions. Consists of:- 1) 44005-1001 Left Hand Outer Tube
- 1) 44006-1001 Right Hand Outer Tube
- 2) 220B0408A Screws
- 2) 44045-002 Drain gaskets
- 2) 44049-024 Fork seals
- 2) 44010-032 Dust shields
- 2) 44043-044 Washers
- 2) 44044-012 Circlip
- 78 KZ1000A
- 77-80 KZ1000 LTD
- 80 KZ1000G, Z1 Classic
- 78-79 KZ750B
- 78-79 KZ650B
-
Out of stock
New Old Stock Genuine Kawasaki P/N: 51023-040 Applications:- H1 500
- H2 750
- KH 500
-
Out of stock
Kawasaki P/N: 13031-1006 This one-year-only crankshaft is in nice shape. Rods and bearings feel good. No flywheel key. 10mm rotor bolt. Applications:- 78 KZ1000A
- 78 KZ1000 LTD
- 78 Z1R
-
Used KZ1000 crankcase with no damage. Bottom only with shift drum ad shift fork. Kawasaki P/N: 14001-107-2J Application:- 77-78 KZ1000
- May fit others
-
Motor # 3A26200H5 This is a matching numbers motor. Numbers are genuine. Crankshaft turns freely. No visible welding. Lower right case has a chipped area as shown. Sprocket cover has insert, as shown. No title. This motor weighs 54 lbs WITHOUT the crate. This motor may be shipped, for an additional fee we can build a shipping crate. Please call us for shipping quotes. Possible low-cost shipping upon request, depending upon where you live. -
Used Genuine Kawasaki P/N's: 21007-1036 Rotor 13196-1006 Clutch Will fit:- 1982-1983 KZ1000R
- 1981-1983 KZ1000J
- 1981-1982 KZ1000K LTD
- 1981-1982 KZ1000M CSR
- 1982-1986 KZ1000 Police
- 1987-1990 KZ1000 Police
- 1991-1995 KZ1000 Police
- 1996-2000 KZ1000 Police
- 2001 KZ1000 Police
- 1981-1982 GPZ1100
- 1981-1983 KZ1100A
- 1983 KZ1100L1 LTD
- may fit others
-
Reproduction 1st Over Piston Kit 66.5 mm Kit consists of:- 4) 13029-058 Pistons
- 4) 13025-046 Rings
- 4) 13002-022 Piston pins
- 8) 92036-021 Circlips
- 73-75 Z1 900
- 76-77 KZ900
-
Nice used crankshaft. Kawasaki P/N: 13031-056 Applications:- 77 KZ1000A
- KZ1000 LTD
-
Out of stock
Complete rebuild kit. OEM Kawasaki P/N: 43041-001 This caliper has new bleeder, New brake pads, and has been powder coated. Applications:- 72 H1B
- 73-75 H1 500
- 76 KH500
- 72 H1B
- 72-75 H1B
-
We are parting out a 71 Sportster. According to our parts book, these will fit 70-71, may fit others. The bore is 2.999" when measured in our warehouse at about 40 degrees Fahrenheit. No broken fins, comes with used piston & rings. Harley P/N's:- 16464-70
- 16465-70
-
Out of stock
OEM Kawasaki P/N: 33001-046 Date code stamped 311. Has some minor pitting, as shown. Has been powder coated. Sold as shown. Applications:- 73-75 Z1 900
- 76-77 KZ900A
-
New Old Stock Kawasaki P/N: 11005-051 Center cylinder, Type 2 The perfect part for the perfect bike Application:- Late 69-72 H1 500
-
Front end fork assembly with wheel. We recently purchased a small warehouse of parts. This is in decent shape, front fender has some warping from storage. Front wheel is not bent. Tire looks okay. Not the original tire. Not a lot of miles on the front end. Front brakes are not working. Throttle housing still good. Has throttle lock. Sold as complete setup or will part out. Low cost shipping available upon request. Location: Gravestone Building -
Out of stock
Genuine Kawasaki Parts ~ Used Give your project a nice added touch! Triple clamp has been freshly powder coated & includes new bolts that we have manufactured here in the U.S. Semigloss Black Powder Coated. Sold as shown. Includes Kawasaki P/N: 44039-045 Upper Triple Clamp Kawasaki 46012-008 Top Clamps (qty 2) 44041-048 Triple Clamp Pinch Bolts (qty 2) 44041-038 Steering Stem Bolt (qty 1) 92020-007 Steering Stem Nut (qty 1) 410B0800 Washer (qty 1) 461F0800 Spring Washer (qty 7) 92007-002 Bolts (qty 4) Applications:- 73-75 Z1 900
-
Front Cylinder Head Made in 1955 only Harley P/N: 16702-55 Intake port has 12 d-ring holes, which should be 6. Overall in very good shape. Applications:- 1955 FLH
-
Out of stock
We removed this wheel from a Z1 900. Very nice drum. We can remove the drum for lower-cost shipping. Can also replace to 18" for additional cost. See video below. Applications:
- 73-75 Z1 900
- 76-77 KZ 900A
- Late 73-75 H2 750
-
Kawasaki Genuine Part ~ REBUILT Kawasaki P/N: 44039-048 Nice, ready-to-go fork bridge set, complete. Rebuilt with quality bolts and hardware made by Johnny's. Includes:- 44039-048 Upper stem
- 44037-053 Lower stem
- 92007-031 Bolt
- 92022-230 Washer
- 46012-010 Lower handlebar holder
- 46012-008 Upper handlebar holder
- 73-75 H1 500
-
We believe these heads are for the 1971 Sportster. May fit others. They appear to be in very nice shape. Came from a 1971 with a blown transmission. One fin may have some damage. Chrome is not nice on the rocker boxes, as shown. Watch movie for a closer look: Harley P/N:- 16673-71 Front
- 16674-71 Rear
-
This piece came from a vintage drag inventory we recently acquired. Not sure if it is from a 1979 or 80 model as the part numbers differ. Should fit either, but the tubes must be used with the lower legs. Possible low-cost shipping upon request, or local pick up if preferred. WILL SEPARATE. Sold as shown - no returns -
Out of stock
This wheel has new bearings, seal & spokes. Genuine style spokes Powder coated, new D.I.D. rim Product Number: 41074-022 Application:- Z1 900
- ALL H2 750
- 72-75 H1 500
-
Right Carburetor Outer VM28SS Mikuni New Kawasaki Genuine Parts ~ New Old Stock Kawasaki P/N: 16001-1154 Application- 1979-80 KZ1000A
